Saab 93 Key Fob Replacement
Saab key fobs with 93 keys could be costly to replace. However the procedure is simple.
You'll require a phillips screwdriver that is flathead and some patience. Simply insert the screwdriver into the middle of the case and slowly work it open.
It is a good idea to have spare keys and fobs. They could save you from being stuck or having to pay towing fees.
How to replace the battery
All car key fobs that allow and lock the vehicle remotely are equipped with batteries inside that will eventually go out. When that happens owners can replace the key fob battery themselves in just a few steps. To remove the old battery from the key fob and replace it with a brand new one, you must open two flaps made of plastic on one side. The replacement battery is an ordinary coin cell CR1632 and the procedure to install it is straightforward.
After you have removed the emergency key, apply the flathead screwdriver to a small piece of wood to break the case. Do not force the case too hard because the electronics are delicate and could be damaged by too much pressure.
Saab created some fantastic automobiles. Many of them are still in circulation today. One of the big problems with these cars is their ignition keys. They can become stuck or even fall off over time. If the Saab owner loses their sole working key, it can be quite costly to buy an additional key at the dealer, since they must replace the entire computer module, and then program it with the new key to convince the vehicle that you're not trying to steal it. The good thing is that you could save a lot of cash by simply replacing the case instead.
How to remove the manual key
Batteries are in every key fob used to lock and unlock vehicles. These batteries have a limited lifespan. If you're like the majority they will go out at some point. It's easy to replace the batteries that you can use to operate the key fob manually. The only tricky part of the procedure is taking out the old battery from the case. But with patience and a flathead screwdriver, you can accomplish the task.
After you've installed the new battery, it's now time to reassemble the entire thing. To accomplish this, you'll need open up the replacement key fob case, which is done by inserting a flathead screwdriver into the slot located in middle of the case. Be gentle with the case until you are able to remove it.
You may need to re-program the new key fob in case your previous key fob failed to establish its connection to the car's security system. saab ignition key replacement can do this by using the manual learning method to add a new fob for your 2010 Saab 9-5. This method does not cause the loss of previously learned keys. You can continue to use existing FOBs, if you require reprogramming them. To initiate this procedure the FOB that is to be programmed must have a mechanical key cut that matches the one of the vehicle.
How to Change the Case
If you're replacing the battery or the manual key it's recommended to replace the case too. The cases tend to wear out quickly, especially after heavy use. Switching the case on your SAAB 9-3 is a relatively simple process, and you don't even need any special tools to do it.
To swap the case, you'll need to first remove the manual key from your key fob. This can be done by pressing the blue SAAB logo on the fob and pulling the manual key out. The key fob can be sticky sometimes, so it may take a little amount of force to get the key out.
Once you've removed that manual key, you're now able to start taking the electronics from the case. To do this, you'll require a small flathead screwdriver. Be gentle with your screwdriver to avoid cause damage to any electronic device. Once you've removed all electronic components, you can begin taking off the battery. Once you've changed the battery, you'll be able to put everything back together in an entirely new case. You can buy cases online at an affordable price.
How to Program the New Key
All key fobs, that permit you to lock or unlock your vehicle remotely, contain batteries. However they are limited in their time of life. It is crucial to keep in mind this and replace the battery in your key fob every three to four years. Fortunately it is a simple procedure that can be completed at home. All you need is a little patience and an incredibly small screwdriver for phillips screwdrivers.
The first step is to remove the manual key. This can be done by pressing the blue SAAB logo on the key fob and pulling the emergency key out. The key should be able to slide out using some force. Once you are able to open the key fob then you can remove the battery that was in it by gently pushing the screwdriver into the slot in the middle of the case. This will split the case, making it easier to access the electronic components.
It is now time to program the key. You can do this by following the steps in this video by YouTube user Cyclone Cyd. This is a fantastic video channel that offers instructions on how you can carry out basic maintenance and repair work on vehicles.
The key fob is an excellent way to have an extra key for your car in case you lose or break it. You can buy a new key fob online or at a local locksmith store, such as United Locksmith. The cost is much cheaper than a dealership which will charge you for the key and programming it into the car.
